CRT Gaming

I was watching Slacker (1991) and this scene reminded me of myself.

cross-posted from: https://feddit.nl/post/22643315

Rescued old CRT I put a lot of work in. Was totally dead when I got it, rescued it to be almost perfect again.

It still has an intermittent horizontal size issue and the power button has some cosmetic wear. But at least the power button works, it used to only work when you would hold it down.

Be sure to enable the audio for some good retro tunes coming from the monitor.

Most people are over-charging for old, worn-out TVs on places like Craigslist and Ebay, now that people are realizing how much better they are for retro gaming. I saw this one for $25 and had to check it out.

I had to clean up the corrosion in the remote to be able to change to the AV input, but it works well enough. Threw it on the kitchen counter to test it out.

The VCR in the bottom still works great too! I'm a total noob to this as I've only ever set up emulators on a regular computer. How difficult is it to set up something like a RetroPi? Or is there a better option?

This is were I found it. I only remembered to take a picture when I already put the thing into my car. It was laying tube down on the fridge.

This was also my first time working on a CRT. Was kinda scary, but nothing happened in the end. Not even a spark when discharging. Guess these newer sets all have a resistor that drains the voltage built in (this TV is from November of 2002).

The power cable uses a connector, so I could just remove the cable and solder a new one to it. Soldering it directly to the board would have probably looked cleaner, but I guess this worked well too. I simply cut off one end of a normal power cable and soldered it to what was left of the existing one. I planned on using heatshrink tubes, but they already shrinked while soldering. I just ended up using electrical tape instead. Not the cleanest soldering work, but it does the job.

This is how it ended up looking inside the TV:

I wanted to be on the safe side when turning the CRT on for the first time, so I did it outside.

It did power on, and looks pretty damn good!

As it turns out, the tube was actually made in the UK. I think that's pretty cool, since everything has to be made as cheaply as possible today. The whole thing seems very well built in general, Rubycon capacitors everywhere.

#

Of course I don't have the remote for it, so I didn't change any setting when taking these pictures. The black levels were still pretty bad, and geometry could be better as well. I ordered a remote to dial everything in, I hope it looks even better after that.

I tried to go for an 80's NES theme. Not perfect but not bad.

I tried to go for an 80's NES theme. Not perfect but not bad.

Hooked up to tv

Nes & Sega (Channel 3)

N64, ps2, vhs

Hdmi converter for

Roku, Nintendo Switch, PS3

The Xbox is softmodded and the video is set to 480i non-widescreen. Any idea why it might not be outputting? What I see is the intended output on my 4k tv, but the CRT is a 45° slanted, scrolling, monochrome image that's heavily warped. My first though was that the softmod had something to do with it, but I've seen this question asked before without any answers.

I have a Triniton Wega (480i) that I'd like to use as a separate monitor for streaming VHS rips and pixely PC games. My computer is a Win11 machine with a 2080, and I just tried usb-c output of the 2080->hdmi->component converter->TV and (to no one's surprise) it didn't work. I used Nvidia's custom resolution to use settings people have suggested online, but my TV would only accept the signal before I OKed the settings then it goes back to fuzz. Does anyone have any suggestions for what I should try or change before resorting to buying a second GPU?

Mister fpga setup with games on the nas. Using an ironclad board.

@crtgaming s-video is a huge improvement over composite, make sure to use it if you have it