The device should be as close to the network as possible (i.e. a router) and have compelling and understandable hardware that could be upgraded over time.

So... they made a router. Originally using PowerPC, now on ARMv7 (poorly only their mobile MOX already is on ARMv8).

Where to get it

Originally they gave the devices away for free, under the agreement that the users contributed the Sentinel analysis data.

Then they opened an indiegogo campain, which far exceeded their expected amount of funding.

Afterwards they had their own webshop, which is now discontinued.

Instead, these stores are available:

Rubytech DE (The strangest signup method I ever had :) but all fine)
Discomp CZ
Amazon

Note: they sent me an additional Tshirt, ethernet cable and tube scarf, which is... interesting, but could be considered waste.

Tbh, I use the tube scarf daily :D

Poorly they didnt add any stickers!

Also, they dont have a good system to determine the recipient country, so I have an additional power supply cable for another country.

They also included a wall mount, with a set of perfectly fitting, longer screws.

All screws have regular phillips heads.

Software

They took OpenWRT, but extended it a ton. As they have 8GB of storage and 2GB of RAM, they can do stuff way above the minimum hardware requirements of OpenWRT.

They have a graphical package manager in the WebUI, and use BTRFS snapshots for atomic updates. Which is totally cool!

That was over 10 years ago and the first router they made is still supported with updates.

Hardware

The data sheet can be obtained here.

The "Omnia Wifi6" I got uses a bit outdated hardware, similar to my Thinkpad T430. They will very likelybswitch to m.2 slots and ARMv8, so you may want to wait for such a revised model.

The current Omnia has 3 mini-PCIe Slots, 2 USB-3 ports and a ton of pins accessible from the inside.

Picture of a disassembled Omnia Router

The left one supports USB, and below you can plug in a SIM card and use an 3G/4G/5G card. With an additional package, this can be used to automatically fallback to cell network, when the regular connection fails.
The middle one is just mini-PCIe
The right one supports mSATA so with a simple adapter you can use SATA SSDs for near-native speed. (I want to do that, but it may need an additional power supply)

Article picture of a mSATA to SATA adapter

And, of couse in the front it has fancy RGB LEDs. They are used as indicators for the running state, and for the action you do by pressing the "Reset" button.

In the back it has 4 ethernet sockets, 1 WAN ethernet socket to connect to the internet, one SFP socket for a fiber connection, a multi-purpose button and a power socket.

The button in combo with the LEDs is used for various things like reboot, reset, update, update from local file, update from internet.

Setup

To set it up, connect it to power and with one of the LAN (not WAN) sockets to a Laptop, using ethernet.

Right, before setup it doesnt open a wireless connection! This was confusing for me but really make sense.

In the browser enter http://192.168.1.1 and a very nice graphical WebUI guides you through the setup.

If you use it over LAN, accept the self-signed TLS certificate in your browser, then HTTPS should work.

Applications

It runs a highly extended variant of OpenWRT. There is a huge amount of software. It varies from preinstalled installable through packages, from Foris WebUI integrated to advanced, requiring the normal OpenWRT LuCI or requiring configuration through the terminal.

An incomplete and chaotic overview:

file server: SMB, DLNA, encrypted storage, mdadm
Transmission bittorrent client
OpenVPN server & client
Wireguard (advanced)
Nextcloud, Syncthing (both have acessible login pages from the main WebUI)
Tor
Adblock
Dynamic firewall
haas: honeypot as a service (needs a public forwarded IPv4 address)
Turris Sentinel: security data collection service, analyze incoming threats (the use they originally intended)
Librespeed: lightweight network speed test
support for LXC containers to run your favourite Linux distro
schnapps to manipulate BTRFS snapshots
LAN monitoring with PaKon and Morce

NOTE: the data collection service "Sentinel" is opt-in and disabled by default.

DNS

The DNS Server is not set, I used nic.cz with DNSSEC, other providers like Cloudflare and Quad9 are also available, just like manual setup.

DNSSEC works with a single button press, without any issues!

Configuration

You can configure things with a config file, that you insert over a USB stick.

Storage

You can plug in an external drive (USB of course, but I want to try mSATA to SATA) and it formats it and moves all data on there.

It sets up different RAID systems, I dont know if encryption is supported.

So, you have over 7 different ways to host a fileserver on there, up to a full instance of Nextcloud. This is crazy!

Wifi Routing

You can open 2 Wifis (no idea how that works) and each can also have a separated Guest network.

Security:

By default, WPA3 with WPA2 fallback is used. I changed it to WPA3-only, as WPA2 is vulnerable to attacks (see this video on how to sniff passwords with Kali Linux, which requires a custom kernel driver)
2 Guest networks possible, I highly recommend to use those for everyone apart from Admins
VLANs are also supported, and need to be enabled.
Reminder: before first configuration, no Wifi is enabled. There is no initial password set.
you can have different passwords for the admin WebUI and ssh.

The reach is great, but roughly equal to the modern Fritzbox we already have, which only has a single, hidden antenna.

The time to connect to the Wifi is a bit longer than at the FritzBox.

Community & Support

Their code is all hosted on the CZ.NIC Gitlab.

The Turris team can be contacted via email and they respond pretty quickly.

The same contact is used for repairs.

They also have a Discourse Forum for a long time, where people can exchange bugs, issues, software and hardware mods, adapters etc.

Other fun stuff

The founder of Turris has a Blog

you are viewing a single comment's thread
view the rest of the comments

[–] [email protected] 3 points 3 months ago (1 children)

Nice! Any reason why you run that?

[–] [email protected] 6 points 3 months ago (1 children)

Part of it is the community. I really like the OpenWRT community, but it's harder to engage with them when you run a downstream distribution.

But also I'm a bit of a hacker (in the traditional sense). I like to experiment with custom builds of OpenWRT. (And FWIW, their build system uses the same menuconfig as Linux.)

[–] [email protected] 2 points 3 months ago

Really cool!

I would also be interested in hacking that router.

For example move as many drivers as possible into userspace with FUSE, to reduce attack surface.

You could even use USB for the network cards.

This is a thing when people "harden" hardware, to contain nothing with direct access to the RAM.