moody

Currently running Nobara, and having audio annoyances.

Any time any app loads anything new, it will switch my audio device back to default. For example, if I open a playlist in VLC and choose my speakers as the output device, when it's done playing one file, it will open the next one and start playing audio through the headphones.

If I'm watching a video on Youtube and choose speakers, as soon as I leave the page it goes back to headphones.

Is there a way to prevent the device in use from switching back? If I switch device, I just want it to stay on that device until I choose to switch back. I literally never want it to switch on its own. ATM, the only way is to manually go it and change the default every time instead of just clicking the checkbox in the volume popup.

This is a recent issue, and I don't know what has changed to cause it. There seems to be no rhyme or reason as to which games work and which ones don't. My monitor's resolution is set to 2560 x 1440 in the display settings, but some games don't recognize it.

Of the games I have installed, Subnautica, Dark Souls III, Sekiro, Control, Hades, and Hi-Fi Rush think my native resolution is 1896 x 1067 and they won't let me change it to anything higher than that.

Elden Ring, Ark Survival Ascended, and Returnal detect my resolution correctly and work fine.

This is all from Steam without any custom launch settings, and with and without gamescope. I've tried custom resolution command line options for Subnautica and that hasn't helped either.

I'm running an RX 6700 XT on Nobara with everything currently up to date. I'm not sure when this issue started, but it's recent, probably within the last week or so. I've definitely run Control and Sekiro at the correct resolution before, but in my recent testing they no longer work right.

Does anyone know what could be causing this? Why some games work fine and others don't?

I haven't bought from Amazon in several years, but I made an exception for this deal. I've never seen this go below $80 before.

Are there any software issues I may/should deal with when doing a full system upgrade? I'm going from AM4 to AM5, so new CPU, motherboard and RAM.

It should be pretty straightforward under Linux, right? Just swap my drives over and boot up? I've only ever done single upgrades at a time, never a full generation.

So it's a SFF case meant for NAS use. It has 5 slide-in 3.5" drive bays and can only handle a low-profile PCIE card.

I'm thinking of picking one up and mangling it to force in a 2-slot GPU. I want to basically remove the drive bays and the PCB with the SATA slots, ditch the PSU frame, move the motherboard frame back or flip it around, and 3d print a new backplate for the case.

I'd stick the PSU where the drive bay used to be and run an extension to the back of the case, and then there should be room for a full-sized GPU mounted vertically in the case.

Do you think this would be achievable? Am I crazy for even thinking about it?

Now if only I could also fit an AIO in there.

EDIT: Link to the case - https://www.jonsbo.com/en/products/N1.html

I've had the game running fine for months, but experience constant crashes if I have foliage and fluid interaction enabled. Has anyone been able to run the game with this on?

Currently on Pop!OS running a 6700XT, and having the issue under both X and Wayland.

Is anybody else dealing with this? In game mode updates install normally, but if I go into desktop mode, updates stall and never finish downloading. And unfortunately you don't get to install desktop updates from game mode.

My internet connection works fine on firefox, and is plenty fast, so it's not a connectivity issue. I'm not sure what's going on.

A friend of mine was a gamer many years ago but hasn't been gaming in a while. They run a Mac and I run a PC. What are some good patient games we can play together?

Every time I use calibrate_probe, I get the message "The SAVE_CONFIG command will update the printer config file with the above and restart the printer."

When I click Save Config, it restarts the firmware, and then I get the warning "Option 'z_offset' in section 'bltouch' must be specified."

If I go check my printer.cfg, the [bltouch] section now has z_offset commented out with the old value and I have to remove the comment and copy in the new value.

Am I missing something? What am I doing wrong?

I'm getting increasingly frustrated trying to get my printer calibrated. I've done a bed calibration using screws_tilt_calculate, and that's all nice and good. Got a bed mesh variance of 0.19mm which seems great.

Now for the z-offset, it won't let me get the nozzle low enough. No matter how low I set the Z minimum, it won't let me get closer than about 0.5mm to the bed. I've tried setting the position_min in [stepper_z] anywhere from 0 to -9 and I get the same result every time.

If I raise the bed, the probe adjust its height accordingly, so the result is the same.

What can I do to fix this?

I picked it up and have been playing it. The first day, it seemed to run fine, but today I've been having a ton of trouble with it. I'm struggling to go 15 minutes without crashing, and when it does crash, Steam stops responding entirely until I reboot.

Edit: I can't explain why, but after checking my logs, whenever my computer full-crashes, it's apparently caused by bluetooth, despite not having any connected bluetooth devices. I've disabled the bluetooth service, and now the game only crashes to desktop. Small wins, I guess.

Another edit: I appear to have fixed my problem. I installed gamemode via apt, and added 'gamemoderun %command%' to the launch options in Steam. Haven't crashed since.