Rangelus

joined 1 year ago
sorted by: new top controversial old
National's new roads a trade-off for safety, public transport, local roading - opposition parties in c/[email protected]
[–] [email protected] 2 points 2 weeks ago (1 children)

I must be confusing it with Auckland's recently cancelled project, I remember a bunch of money being spent to purchase land.

I mean, I wish they'd build shit. Total agreement here. It needs to be done, just do it!

National's new roads a trade-off for safety, public transport, local roading - opposition parties in c/[email protected]
[–] [email protected] 2 points 2 weeks ago (3 children)

Oh absolutely, sunk cost fallacy is a problem. No disagreement there.

However, my point is cancelling a project doesn't remove the need. We need better public transport, we need ferries, we need infrastructure upgrades. All of these things need to happen, and the longer they are put off usually the more they will cost. So it's not so simple as a sunk cost, as cancelling a project then doing it again later may very well end up costing more in the long run than the over run cost of the initial project. Case in point, the ferries.

I will admit, though, I know less about the wellington light rail project. I was under the impression that a lot of the cost being spent was paying for land that was needed for the project, but you can probably inform me more about this. I'll just say, rail is still needed (or some form of mass transit system).

National's new roads a trade-off for safety, public transport, local roading - opposition parties in c/[email protected]
[–] [email protected] 2 points 2 weeks ago (5 children)

Infrastructure is expensive, and often goes over budget. It is hard to deliver large projects on time and on budget. Any builder will tell you how often a simple house build goes over time and budget.

Crying about incompetency is silly when the alternative seems to be to throw away money that has been spent for no gain. We have lost all the money spent on the ferries, plus a penalty, for no fucking gain at all. All the money spent working on ALR has been flushed down the toilet. It's fucking insanity.

The answer is not throwing away projects because they cost more than anticipated, it is finishing projects and figuring out how to do it better next time. New Zealand has seriously terrible infrastructure problems and they can only be solved with money, and a lot of it.

An explainer on the maths "crisis" in c/[email protected]
[–] [email protected] 10 points 2 weeks ago (1 children)

This stuff pisses me off so much.

Educational curricula should be independent of politics. It should be solely based on educational research and achievement statistics, not fucking ideology.

NASA's solar sail successfully spreads its wings in space in c/[email protected]
[–] [email protected] 2 points 2 weeks ago* (last edited 2 weeks ago) (3 children)

Cheers mate. Neat stuff!

I wonder how much force a sail of that size is expected to produce?

Housing reforms mean a free market and 'extremely ugly buildings', developer says in c/[email protected]
[–] [email protected] 2 points 2 months ago

The only thing I'm concerned about is the continued creep of housing developments into productive farmland.

If developers want to increase density of housing in current areas, that's a good thing! I don't particularly care about how stylish a development is at this point in time. Besides, current cookie cutter housing is all ugly anyway.

Teenage boy threatened with machete at Albany Bus Station in attempt to steal his shoes in c/[email protected]
[–] [email protected] 3 points 3 months ago (1 children)

I agree with you, and I think it's interesting to look at why there is a short term uptick in youth crime.

Something something cost of living crisis something something

Te Pāti Māori wants to establish its own parliament in c/[email protected]
[–] [email protected] 4 points 3 months ago (1 children)

But the ambiguity comes from the crown ignoring the original, Te Reo document, in favour of the translates English version, then ignoring that as well.

Seagliders' 35-minute trips to Auckland closer with $145m deal in c/[email protected]
[–] [email protected] 4 points 4 months ago

I want these to become a thing, because they're awesome. But I doubt it actually will.

Plus, there are much more efficient ways to move large numbers of people. Still, ground affect craft are neat.

[Troubleshooting] Big stringing problem with flsun SR and Orcaslicer in c/[email protected]
[–] [email protected] 2 points 4 months ago

It's all good mate! Thanks for the suggestion. When I first started printing I had that exact issue.

[Troubleshooting] Big stringing problem with flsun SR and Orcaslicer in c/[email protected]
[–] [email protected] 3 points 4 months ago (2 children)

Hey mate, I keep my filament in a dry cabinet at 5ish% humidity, and I've had the same results with two different filaments in there. I even chucked my filament in a food dehydrator at 40C for 12h with no effect. I'm pretty sure the filament is dry!

Does anyone print planter heads? in c/[email protected]
[–] [email protected] 2 points 4 months ago

I love these! Thanks for sharing!

37
[Troubleshooting] Big stringing problem with flsun SR and Orcaslicer (lemmy.nz)
 

Ok guys, I'm breaking down and posting here to see if anyone has any ideas. I'm greatful for any advice.

I have an upgraded flsun SR. I recently lost my computer (psu issue, waiting for replacement) and I took this opportunity to switch from Cura to Orcaslicer.

Over-all I'm very happy, and getting some good speeds, but I just cannot remove stringing no matter what I try:

  • Retraction from 0-7mm. After about 3mm, no further effect
  • Retraction speed from 30mm/s-50mm/s. No noticable effect
  • Travel speed and acceleration both high (up to 350mm/s and 6000 accel. No effect
  • Temp from 205-215 with no effect
  • Dried filament and different colours, no effect
  • Wipe on retract on and off, up to 2mm wipe distance and 100% retraction. No effect
  • Messed with scarf seams on and off, no effect
  • No effect from layer heights

My setup:

  • Printer - FLSun SR running klipper with a speede pad
  • Filament - Esun PLA+
  • Upgrades - Deported fans, OMG v2 extruder, volcano hotend and high flow cht nozzle
21
Help with stringing after shifting to Klipper (lemmy.nz)
submitted 11 months ago* (last edited 11 months ago) by [email protected] to c/[email protected]
16 comments fedilink
 

Background:

I am running a mostly stock flsun Super Racer, which had been running pretty well on Marlin. I was having a few problems with print quality at high speed, and in an attempt to improve this I bought the flsun Speeder Pad, flashed it with stock klipper, and got it all up and running. So far so good.

I have been trying to get rid of an annoying stringing issue that I never really had on Marlin, and the more I try to remedy it, the worse it's getting.

The image is from my latest retraction tower test after re-calibrating pressure advance and rotation_distance. I'm really not sure where to go from here.

Settings from the above test:

  • Esun PLA+
  • 220C (for maximum flow)
  • 1000mm/s acceleration (low for a delta)
  • 0.1mm z-hop on retract
  • Firmware retract control running in test tower mode, 0mm start, 0.1mm factor
  • Pressure advance of 0.236

Upgrades from stock:

  • Lighter hotend housing
  • Deported fans
  • Fan ducts

Any advice is greatly appreciate!

UPDATE: It was the filament. I grabbed a spool of grey from my drying cabinet, and only later (after much hair pulling!) realized it was the budget filament I'd bought to try. Switched it out to some good quality esun PLA+ and the stringing practically vanished! See image for final stringing test.

Final retraction settings: 3.5mm at 35mm/s.

I would like to thank everyone for their help! Lemmy is always the best place to get advice!

12
Inquiry into the current and future nature, impact, and risks of cryptocurrencies final report has been released. (selectcommittees.parliament.nz)
 

I didn't know the final report had been released already, but after an interview on RNZ National today I went looking for the actual report.

Some very interesting recommendations. Here are some highlights:

Policy settings

  1. We recommend that the Government adopt policy settings to encourage developments in digital assets and blockchain in New Zealand.

Regulatory frameworks 2. Because it is early in the development of digital assets and blockchain, we recommend that the Government and regulatory agencies proceed carefully and do not design and implement a fully integrated and consistent regulatory framework for digital assets at this point in time.

Primary regulator role 8. We recommend that there should be no primary regulator for digital assets, as digital assets cover a spectrum of use cases, well beyond investment.

“Blockchain-sprints” 11. We recommend that the Digital Assets Cross-Agency Working Group hold “blockchain-sprint” equivalent or similar events to develop new ideas and strategies for industry growth.

Education 14. We recommend that secondary and tertiary educational institutions consider developing courses in relation to digital assets, blockchain, and the broader Web3 context, as part of a wider focus on technology (and its place in New Zealand’s future).

Central bank digital currency 22. We recommend that the Reserve Bank continue with design work on its central bank digital currency.

Interesting things here. Clearly the recommendation is for the government to embrace and encourage Blockchain technology, and not to regulate it too heavily.

I'm curious to see what comes of this.

13
Case of missing Christchurch woman Yanfei Bao now homicide inquiry (www.rnz.co.nz)
 

Sounds like the worst case scenario has come to pass, unfortunately. Very sad news.

13
Just received a scam phone call (lemmy.nz)
 

First time this has happened to me here in NZ. Just received a call to my cell, from an 027 number. A robotic voice then said

This is a One NZ urgent notice. Your account is about to go out of service. Press 1 for English, and 2 for Chinese

Of course I hung up, and checking my One NZ app which naturally had no issues. These kinds of things seem to be becoming more and more common. I wonder if more people are falling for them, or if the scammers are just more desperate?

Does anyone know how to report a phone number?

13
Can't figure out how to add new models to docker install of Automatic1111 (lemmy.nz)
submitted 1 year ago* (last edited 1 year ago) by [email protected] to c/[email protected]
28 comments fedilink
 

Hi guys,

I used the Docker install from here. It was easy to get Automatic1111's web interface up and running, but I'm trying to add new models and I can't figure out how to do it.

I've created a /data/StableDiffusion folder (which didn't exist), and added model files from /data/models, with no effect. I've added them to /data/models/stable-diffusion (which already exists), with no effect. Is there another location where the files are stored? Do I need to do something else to get them to work?

ETA: Discovered I was using the wrong file type (.pth) instead of the correct one (.ckpt). When I tried it with that file type it works perfectly. Thank you everyone for your quick responses and help! Y'all were way faster and more helpful than Reddit!

1
Lemmy android client (lemmy.nz)
 

What client, if any, do you guys use on your phone? I've been using Jerboa, but it has its problems so I'm wondering if there's a better option?

38
So that's it r/newzealand? (lemmy.nz)
 

So, I see r/NZ is back. That's it? What an anemic protest. I guess I'm honestly surprised more people don't care. I expected the protest to go on longer, but I guess I overestimated how much the average user cared about this.

Unfortunately, I think it probably means we won't see a lot of growth in Lemmy now. Shame.

view more: next ›