3DPrinting

15548 readers

358 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago

MODERATORS

[email protected]

Layer shift sanity check (lemmy.world)

submitted 1 year ago* (last edited 1 year ago) by [email protected] to c/[email protected]

3 comments fedilink hide all child comments

Curious if I can get a sanity check off my problem diagnosis (or alternate theories!)

I tried a long print today and wound up with a 1/2 inch layer shift on the x-axis near the end of a long print, taller than most I've done, not certainly not the tallest.

It occured on a spool I just opened a few days ago and printed two other ~250g pieces with. I'm very certain that I never lost control of the filament end. My spool in mounted using the stock ender 3 mount on the left side is the gantry and a filament guide arm.

After reading a bit, I'm thinking this was due to the filament on the spool loosening up from a large travel and then binding on itself. Seems the easiest way to fix this might just be to put more space between the spool and the printer so the slack can absorb the shifting without pushing back on the spool and loosening several turns off filament.

I don't think it's heat or any general axis binding as the shift only happened at a single layer, at a hight that I've been able to print through before, and the motion generally appears smooth when I exercise it.

So... Experimentation will probably prove me right or wrong, but before I sink another day of print time... Does that sound reasonable or am I missing a common problem?

Edit: Solved, see comment by @[email protected] for the actual problem. Many thanks to all who provided their thoughts!

top 3 comments

sorted by: hot top controversial new old

[–] [email protected] 1 points 1 year ago

I was having an issue like this last week, and surprisingly, I was able to finish my print by using a new slicer. I was all prepared to go buy a new board for my ender3v2. I had even put a bigger fan on the board to try more cooling but still kept getting it on this large print. I sliced it in superslicer instead of cura, and it printed. Unless you're just eager to spend money and replace parts, not necessarily a bad thing, I would take a stab at a different slicer first.

[–] [email protected] 0 points 1 year ago (1 children)

My initial guess (having had similar layer shifts in the past) is that one of those skinny 'Y' vertical pieces with angled overhangs simply curled up a little too much (shrinking warpage) and eventually the nozzle took a path where it made contact with the raised edge and cause the motor/belt to slip until it continued in the new position.

Ways to prevent include much higher cooling for those curling points (super slow high fan), or enclosure of the entire unit to mitigate warping.

Sorry for late response, hope it helps or you solved it.

[–] [email protected] 1 points 1 year ago

Winner winner chicken dinner! This is EXACTLY what happened. I reprinted again after tightening belts, fixing bed wobble, and re-leveling, and kept a closer eye on it this time. The nozzle was indeed catching on that "Y" support due to the edge curling up. Wasnt enough to kill the print this time, but enough to make me nervous...

Ironically, the thing I'm printing is an all-in-one case so that I can segregate the PSU, main board, pi, and controls from the printer itself to enclose it and have better temp control!