this post was submitted on 27 Sep 2024
81 points (96.6% liked)
Linux
48332 readers
1017 users here now
From Wikipedia, the free encyclopedia
Linux is a family of open source Unix-like operating systems based on the Linux kernel, an operating system kernel first released on September 17, 1991 by Linus Torvalds. Linux is typically packaged in a Linux distribution (or distro for short).
Distributions include the Linux kernel and supporting system software and libraries, many of which are provided by the GNU Project. Many Linux distributions use the word "Linux" in their name, but the Free Software Foundation uses the name GNU/Linux to emphasize the importance of GNU software, causing some controversy.
Rules
- Posts must be relevant to operating systems running the Linux kernel. GNU/Linux or otherwise.
- No misinformation
- No NSFW content
- No hate speech, bigotry, etc
Related Communities
Community icon by Alpár-Etele Méder, licensed under CC BY 3.0
founded 5 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
You've got it backwards. A firewall blocks everything, then you open up the ports you want to use. A standard config would allow everything going out, and block everything coming in (unless you initiated that connection, then it is allowed).
So the question you should be asking, is what services do you think you're going to be running on your desktop that you plan to allow anyone on the internet to get to?
Not entirely clear but perhaps OP is talking about blocking unwanted outgoing reqjests? E.g. anti-features and such since they mention traffic from their apps.
Possibly? The way I read it, it sounded like OP wasn't really even sure what a firewall does.
no, not really. on linux that depends on the default policy of the corresponding chains, so it's configurable. I don't think all common distros default to reject either.
@Shdwdrgn @Cornflake_Dog false. a firewall can indeed have a default block everything policy, but this is still a configurable option
Sure it CAN be configured, but the typical policy of firewalls is to start from a position of blocking everything. From what I've seen, on Linux the standard starting point is blocking all incoming and allowing all outgoing. On Windows the default seems to be blocking everything in both directions. Sure you could start with a policy of allowing everything and block only selected ports, but what good is that when you can't predict what ports an attacker might come from?
@Shdwdrgn on Linux, the firewall with zero custom rules always allowed everything. did that change in very recent kernels? if that's the case, I'd expect a lot of lost acces to remote servers
Most of my experience is with iptables, but yeah, I think until you start adding rules nothing is implicitly denied? Once you enable a couple of initial rules then you should have good blocking from the outside while allowing internal traffic to connect freely. It doesn't get in your way until you start using it, but then it doesn't take much to get it going.
Please stop giving bad advise. The local firewall is not the same as the public firewall and nat on the router. Your comment is incredibly misleading. You can have no Firewall and the services will not be available publicly
What are you talking about? You're assuming that every residential router is going to have some kind of firewall enabled by default (they don't). Sure, if OP has a router that provides a basic firewall type service then it will likely block all incoming unauthorized traffic. However OP is specifically talking about a linux-based firewall and hasn't specified if they have a router-based firewall service in place as well so we can only provide info on the firewall they specified. And if you look at UFW, the default configuration is to allow outgoing traffic and block all but a very few defined incoming ports.
You're also making the assumption that OP is using NAT, when that is not always the case for all ISPs. Some are really annoying with their setup in that they give a routable IP to the first computer that connects and don't allow any other connections (I had that setup once with Comcast). In this case, you wouldn't even need to define port-forwarding to get directly to OP's computer -- and any services they might be running. This particular scenario is especially dangerous for home computers and I really hope no legitimate ISP is still following a practice like this, however I don't take anything for granted.
Regardless of what other equipment OP has, UFW is going to provide FAR better defaults and configurability when compared to a residential router that is simply set up to create the fewest support calls to their ISP.
You know enough to be dangerous...
Why would an ISP assign a public IP to a users device? That wouldn't make any sense. IPs are rare and expensive so that wouldn't waste it on you. Each customer gets one IP and that is shared for all devices via NAT.
What your describing doesn't make any sense
You're right, it doesn't make any sense. And it didn't make any sense at the time either. After setting up the router with a laptop, I moved the connection to the firewall but it refused to connect. When I finally got ahold of tech support they said the connection locks into the first machine that logs in and they had to release it so I could connect the new machine. And just like that the firewall was given a routable IP address and connected to the internet. Stupidest thing I ever heard of, but that's how they were set up. Now this was around 15+ years ago and I would certainly hope nobody is doing that crap today, but apparently that was their brilliant method of limiting how many devices could get online at once.
So some obscure thing you experienced 10 years ago is now the standard? I have been doing this a while and what you are describing is Franky crazy and I've never scene it outside of some business plans with bring your own device.
Who said anything about it being standard? I said I know this CAN happen, and I said it was quite some time ago. We can only hope this insanity isn't still in practice anywhere, but I learned long ago that expecting a corporation to NOT do foolish things will give me the same disappointing results as expecting money to come out of my ass. If there's a manager involved, then something on the tech side is going to get fucked up in the name of saving a buck. Therefore I cannot just assume OP gets a normal NAT address, nor can I assume they have any other firewall type device between them and the internet. With limited data, the best I can do is try and provide some general information, hopefully encourage them to ask more questions or provide more specific information, and just hope they don't have a ridiculously stupid ISP that makes things needlessly complicated.
I fail to see why this is bad advice. Sure you could just disable the firewall on your computer on a local network. But that's under the assumption that you can trust everything on your local network. What if it's a laptop? Do you also trust any public networks you may connect to on the go? Having firewall both on the router and on your computer provides an additional layer of security, and I think that's good advice in general. You can for example set it up to only allow incoming connections when connected to your home network for example.
There is a difference between good practice and fear mongering. You aren't going to lose it all because you didn't turn on the Firewall.
To be fair I haven't configured a firewall either on my laptop. But that's out of lazyness, not out of good practice. Good practice would be to have a firewall enabled. Just because something is unlikely to happen statistically doesn't mean it's bad practice to take steps to protect against it.