Selfhosted

39435 readers

6 users here now

A place to share alternatives to popular online services that can be self-hosted without giving up privacy or locking you into a service you don't control.

Rules:

Be civil: we're here to support and learn from one another. Insults won't be tolerated. Flame wars are frowned upon.
No spam posting.
Posts have to be centered around self-hosting. There are other communities for discussing hardware or home computing. If it's not obvious why your post topic revolves around selfhosting, please include details to make it clear.
Don't duplicate the full text of your blog or github here. Just post the link for folks to click.
Submission headline should match the article title (don’t cherry-pick information from the title to fit your agenda).
No trolling.

Resources:

Any issues on the community? Report it using the report flag.

Questions? DM the mods!

founded 2 years ago

MODERATORS

[email protected]

141

I spent ~$35 on new cables and my LAN speed increased 6x (sh.itjust.works)

submitted 3 months ago by [email protected] to c/[email protected]

60 comments fedilink hide all child comments

After seeing that my wireless speeds were much faster than the speeds I was getting over Ethernet, I decided to invest in some new cables. I didn't know it before, but I saw while I was changing them out that my current cables were Cat 5e. While putting my network together, I had just been grabbing whatever cables I could find in my scrap drawers. Now I have Cat 8 cables and my speeds jumped from 7MB/s to an average of over 40MB/s. It's a much bigger improvement than I expected, especially for such a small investment.

you are viewing a single comment's thread
view the rest of the comments

[–] [email protected] 5 points 3 months ago* (last edited 3 months ago) (1 children)

Ethernet speeds historically were measured in 10/100. In my past life I worked for an a small rural isp. And part of my learning I was taught that cat5 was 8 strands of wire, or 4 twisted pairs. I got very familiar with crimping patch cables. If one strand were cut a network card would negotiate down to its lowest speed and still work at 10mbps. Operating on 4 wire or two pairs. It’s possible with those numbers you had a bad connection, or a broken strand in the cable and it auto negotiated down to 10mbps. To this day I still crimp my own cables, and I own a cheap cable tester to make sure the crimps and cables are good.

[–] [email protected] 4 points 3 months ago* (last edited 3 months ago)

I've a run of around 60 meters of old telephone cables (made out of copper, 4 wires) and I can get 100Mbps on those reliably. I used the old telephone infrastructure on the building to pass network from an apartment to the basement that way.

Not to spec on ethernet on any way, not even twisted pairs but they do work. Unfortunately I can't replace the run with a proper Cat6 cable because there's a section that I can't find where it goes to, it just disappears on a floor and appears 2 floors bellow it inside the main telephone distribution box.

On the distribution box (that is already on the basement of the building) I'm plugging into the LSA connector that goes to the apartment:

The black box you see there is a mikrotik gper that is essentially a PoE switch with only 2 ethernet ports so I can get over the 100m limitation of ethernet. I'm running a cat6 cable from there on metal cable trays for about another 90 meters until it reaches a storage unit 2 floors bellow ground.

Here's a ping test from a machine sitting on the storage box to the router on the apartment:

The router reports this as a 100M full-duplex connection:

If anyone wants to try a setup like this, or just extend ethernet > 100m, it also worked fine with a cheap 5$ 100M switch from Aliexpress and a PoE injector + splitter.

However I eventually got the mikrotik gper for free so I decided to replace it because it should be more reliable.